Injection Mold Tariffs 2026: What a Mold From China, Vietnam, Mexico or the US Really Costs
A mold from China now pays about 40% duty: 3.1% MFN, Section 232 up to 15%, plus 25% Section 301. Vietnam, Mexico, Canada and the EU pay about 15%. IEEPA is gone and molds escape the forced labor tariff. Full stack, worked numbers and buyer questions.

As of November 18, 2026, an injection mold imported into the US from China pays about 40% of its value in duty: the 3.1% normal rate, Section 232 steel derivative duty that tops the first two up to 15%, and the 25% Section 301 China tariff on top. The same mold built in Vietnam, Mexico, Canada, Japan or the EU pays about 15% all in. A mold built in the US pays nothing. The 2025 reciprocal and fentanyl tariffs are gone, and molds are exempt from the new 12.5% forced labor tariff. Most pages ranking for this question still get at least one of those four facts wrong.
This guide walks through the full stack, line by line, with the sources, then runs the numbers on real mold prices so you can see where the break even sits. It is general education, not legal or customs advice. Confirm your classification and rates with a licensed customs broker before you place a tooling order.
What the top search results get wrong
We read the five pages that rank highest for “tariffs on injection molds from China” before writing this. Here is what a buyer would walk away believing from each, and why it is off.
- A 2022 supplier blog “updated April 2026” says plastic injection molds carry a 2.5% tariff. The actual normal (MFN) rate is 3.1%, and the page names no Section 301, Section 232 or any 2025 or 2026 action at all.
- A tariff calculator page gets the China number right at 40% all in (3.1% MFN, 25% Section 301, 11.9% Section 232), but gives no rates for Vietnam or Mexico and no explanation of why the 232 piece is 11.9%.
- A May 2026 cost comparison from a Chinese mold maker lists only the 25% Section 301 tariff, calls it List 4A (it is List 1), and leaves Section 232 out, so its landed cost for China is too low.
- A US supply chain guide last modified July 2026 still describes a 30% China rate “until the end of the 90 day truce” and a 25% rate on non USMCA goods from Mexico. Both were IEEPA tariffs, which the Supreme Court struck down in February.
- A 2026 China mold tariff explainer adds a 20% “fentanyl related” IEEPA duty to reach 48.1%. That duty stopped being collected on February 24, 2026.
The common gaps: nobody explains that molds are a Section 232 steel derivative, nobody prices Vietnam or Mexico, nobody covers the July 2026 forced labor tariff and why molds escape it, and nobody separates the duty on the mold from the duty on the parts it makes. That last one is where most of the money is.
The 2026 duty stack on an injection mold, origin by origin
Injection molds for plastics enter under HTS 8480.71.80, statistical line 8480.71.80.45 “Injection type”. Compression molds are .60. The normal rate is 3.1% (2026 HTS Revision 23), with free entry for most free trade partners on the special column. On top of that sit three layers that matter in 2026.
Layer 1: Section 232 steel derivatives (every origin)
Molds for rubber or plastics were added to the Section 232 steel and aluminum derivative list in a Commerce notice published August 19, 2025, which put a 50% duty on the steel content. Proclamation 11021, signed April 2, 2026 and effective April 6, rebuilt that system: the duty now applies to “the full entered value of imported products, regardless of metal content”, sorted into annexes at 50%, 25% and a temporary 15%.
Injection molds (8480.71.8045) and compression molds (8480.71.8060) sit on Annex III, the temporary reduction list, through December 31, 2027. The Annex III rule is an all in ceiling: where the normal duty rate is under 15%, the normal rate plus the 232 duty equals 15%, as the Congressional Research Service summarizes it. For a mold at 3.1% MFN, that means 11.9% of Section 232 duty on the full value. The June 2026 follow up proclamation, effective June 8, kept the 15% tier and dropped the threshold for the 10% “US metal” rate from 95% to 85% US content.
Two points buyers miss. First, CRS states plainly that Section 232 steel and aluminum duties apply to USMCA compliant goods, so building a mold in Mexico does not escape this layer. Second, the same Annex III list includes injection molding machines (8477.10.90) and their parts, so a press bought abroad lands in the same 15% bucket.
Layer 2: Section 301 on China (China only)
Injection molds were on Section 301 List 1, effective July 6, 2018, at 25%, under Chapter 99 heading 9903.88.01. That tariff is untouched by the Supreme Court case because it rests on a different statute. CRS notes that Section 232 duties apply in addition to Section 301 tariffs, which is how the China stack reaches 40%.
Layer 3: Section 301 forced labor (not on molds)
On July 24, 2026, USTR put a new Section 301 forced labor tariff on 60 economies: 12.5% for China and Vietnam, 10% for Mexico, Canada and India, with “net of MFN” versions for the EU, Taiwan, Japan and Korea. Goods covered by Section 232 are exempt, as are USMCA qualifying goods from Mexico and Canada, according to Holland and Knight and GHY. Because molds are on the 232 list, the forced labor duty does not apply to them. It does apply to most of what the mold produces, which we cover below. The action is being challenged at the Court of International Trade, with no decision as of late October.
One trap: the temporary import line 8480.71.80.20 (molds brought in for testing or repair) is not on Annex III, and one tariff tool shows it at 40.6% from China including the 12.5% forced labor duty. Classification at the ten digit level changes the answer.
What is gone
The Supreme Court ruled in Learning Resources v. Trump on February 20, 2026 that IEEPA does not authorize tariffs, ending the 2025 reciprocal and fentanyl duties. CBP stopped collecting them for goods entered from February 24. The 10% Section 122 surcharge that replaced them ran from February 24 to July 24, 2026 and was not extended; it did not apply to Section 232 goods in any case.
Comparison table: duty on an injection mold by origin, November 2026
| Where the mold is built | MFN (8480.71.80) | Section 232 (Annex III) | Section 301 China | Forced labor 301 | Total duty on mold value |
|---|---|---|---|---|---|
| China | 3.1% | 11.9% | 25% | Exempt (232 good) | 40% |
| Vietnam | 3.1% | 11.9% | None | Exempt (232 good) | 15% |
| Mexico | 3.1%, or free if USMCA qualifying | Tops up to 15% all in | None | Exempt | 15% |
| Canada | 3.1%, or free if USMCA qualifying | Tops up to 15% all in | None | Exempt | 15% |
| Japan, Korea, Taiwan, EU (Portugal, Germany, Italy) | 3.1% (free for Korea and Japan on the special column) | Tops up to 15% all in | None | Exempt | 15% |
| United States | None | None | None | None | 0% |
Sources: HTS 8480.71.80, Annex III, CRS IN12519, Gateway Lines China stack, GHY. Where a free trade rate cuts the MFN rate to zero, the Annex III formula still brings the combined rate to 15%, so the total does not change. Duties apply to the full customs value of the mold as entered.
Running the numbers on a real mold
Duty percentages only matter against real prices. One Chinese mold builder’s May 2026 comparison puts a single cavity steel mold at $10,000 to $18,000 in China, $12,000 to $20,000 in Vietnam and $25,000 to $45,000 in the US or Mexico. Those are a vendor’s ranges, not a survey, and the same page only charged China the 25% Section 301 duty. Here they are with the full 2026 stack applied.
| Origin | Vendor price range, single cavity | 2026 duty rate | Duty paid | Price plus duty |
|---|---|---|---|---|
| China | $10,000 to $18,000 | 40% | $4,000 to $7,200 | $14,000 to $25,200 |
| Vietnam | $12,000 to $20,000 | 15% | $1,800 to $3,000 | $13,800 to $23,000 |
| US | $25,000 to $45,000 | 0% | $0 | $25,000 to $45,000 |
Our arithmetic on the vendor ranges. The result: once the full China stack is applied, Vietnam is already as cheap as China on a landed basis, before freight, and the gap to a US build closes from roughly 2.5 to 1 at the low end on sticker price to about 1.8 to 1. A US mold is still more expensive on paper, but the duty now covers a large share of the gap.
Scale it up and the duty becomes a line item a CFO notices. On a $50,000 mold:
| Origin | Mold value | Duty rate | Duty | Price plus duty |
|---|---|---|---|---|
| China | $50,000 | 40% | $20,000 | $70,000 |
| Vietnam, Mexico, Canada, EU, Japan | $50,000 | 15% | $7,500 | $57,500 |
| US | $50,000 | 0% | $0 | $50,000 |
Read it the other way: a Chinese mold priced at $50,000 has to beat a Vietnamese quote by about 18% and a US quote by about 29% just to break even on duty. Freight is extra. One US sourcing guide puts a 40 foot container from China at $3,000 to $5,000 to the West Coast and $4,000 to $6,500 to the East Coast, against $500 to $2,500 from Mexico. A single mold rarely fills a container, but the spread shows how much distance costs on every trip, including the trips back for engineering changes.
The bigger number: duty on the parts the mold makes
The mold is a one time duty. The parts are every shipment for the life of the program, and parts are where the 2026 forced labor tariff bites. Most molded plastic parts are not steel or aluminum derivatives, so unless a part falls in one of the action’s exempt categories, a part made in China or Vietnam now carries the 12.5% forced labor duty on top of its normal rate, and Chinese parts can also owe their existing Section 301 tariff, which Strix notes is a separate action. Check the exact line for your part. Mexican parts carry 10% unless they qualify under USMCA, which exempts them.
That changes the classic decision. For years the playbook was to build the mold in China, then ship it to wherever you mold. In 2026 a mold built in China and run in the US pays its 40% once. A mold run in China pays a part tariff on every carton. For a program shipping millions of parts a year, the location of the press matters far more than the location of the toolroom.
There is a second link between the two. Under US customs law, a mold you supply free or at a reduced cost to a foreign molder is an “assist”: the statute lists “tools, dies, molds and similar items used in the production of the imported merchandise”. Its value is added to the customs value of the parts, and CBP lets you apportion it over the first shipment, the units produced to the first shipment, or the entire anticipated production. If you buy a $50,000 mold and park it at a molder in Vietnam, that $50,000 rides into the duty base of the parts. Many buyers never declare it.
What buyers should ask before signing a tooling PO
- Where is the mold built, and where does it run? Get both answers in writing. The mold’s origin sets the mold duty; the molding plant’s country drives the duty on every part. When the base, hot runner and machining come from different countries, ask your broker how origin will be determined.
- What ten digit HTS line will the broker use? 8480.71.80.45 for injection molds lands on Annex III at 15% all in. A different suffix or a different heading can change the stack by 25 points or more.
- Is the hot runner priced and shipped inside the mold? Under the full entered value rule, if a $15,000 hot runner system is entered as part of a Chinese mold, it adds $6,000 of duty at 40%. Ask how your broker will treat it.
- For Mexico, does the mold qualify under USMCA, and does it matter? Qualification removes the 3.1% normal rate and the forced labor duty, but CRS says Section 232 still applies, so the combined rate on the mold stays near 15%. For the parts, USMCA qualification is worth far more.
- Are you declaring the mold as an assist on the parts? If you own the tool and it sits at an overseas molder, ask your broker how its value is apportioned across part entries.
- Did you import molds between February 2025 and February 2026? IEEPA duties paid on them may be refundable. CBP’s CAPE process in the ACE portal opened April 20, 2026, and the Court of International Trade certified a class of importers on October 8, 2026.
- What happens in 2027? Two dates matter. The Annex III 15% rate runs through December 31, 2027 and reverts after that. And Proclamation 11077 on robotics and industrial machinery, signed October 28, 2026, imposed no tariffs but gave Commerce and USTR until about April 26, 2027 to report on negotiations. It has not yet named any HTS codes, so molds and presses are not confirmed in or out.
How the mold tariff got here: a timeline
| Date | Action | Effect on a Chinese injection mold |
|---|---|---|
| July 6, 2018 | Section 301 List 1 | 25% added on top of 3.1% |
| 2025 | IEEPA fentanyl and reciprocal duties | Additional layers, later ruled unlawful |
| August 19, 2025 | Molds added to Section 232 steel derivatives | 50% on steel content |
| February 20 to 24, 2026 | Supreme Court ruling; IEEPA collection stops; Section 122 starts | IEEPA layers removed, refunds open |
| April 6, 2026 | Proclamation 11021, Annex III | 232 moves to full value, 15% all in |
| July 24, 2026 | Section 122 expires; forced labor 301 begins | Molds exempt as 232 goods |
| October 28, 2026 | Proclamation 11077, machinery and robotics | No tariff yet; report due about April 26, 2027 |
| December 31, 2027 | Annex III reduction ends | Rate reverts unless extended |
Brandon’s Take
From the tooling side, the headline 40% gets too much attention and the parts tariff gets too little. A mold is bought once. If the 2026 rules push a program to build the tool in China and mold in the US, the buyer pays a one time penalty and gets a domestic supply chain for parts with no forced labor duty and no ocean in the middle. The math that should drive the decision is part volume times part tariff over the life of the program, plus the cost of every engineering change that has to cross an ocean. The mold duty is the entry fee. The other thing I would watch is the December 31, 2027 sunset on Annex III. A large tool ordered today, with its build and sampling cycle, can easily land in 2027, and anyone planning a 2028 tooling budget should price the risk that the 15% ceiling goes away.
FAQ
What is the tariff on injection molds from China in 2026?
About 40% of the mold’s full customs value: 3.1% MFN, 11.9% Section 232 (the Annex III top up to 15%), and 25% Section 301. The IEEPA fentanyl and reciprocal duties no longer apply, and the 12.5% forced labor tariff does not apply because molds are Section 232 goods.
Is there a tariff on injection molds from Vietnam?
Yes, about 15% all in under Section 232 Annex III. Vietnam has no Section 301 China tariff, and the 12.5% forced labor duty that hits most Vietnamese goods does not apply to molds. Parts molded in Vietnam are a different story: they generally carry the 12.5% forced labor duty.
Are molds from Mexico duty free under USMCA?
No. USMCA qualification can remove the normal rate and the forced labor duty, but Section 232 steel derivative duties apply to USMCA compliant goods, so the combined rate on a mold stays around 15%.
Is the Section 232 duty on molds charged on the steel content or the whole mold?
The whole mold. Since April 6, 2026, Section 232 derivative duties apply to the full entered value regardless of metal content.
Can I get a refund for tariffs I paid on molds in 2025?
Possibly, for the IEEPA portion only. Section 301 and Section 232 duties are not refundable under the Supreme Court ruling. Importers file through CBP’s CAPE process, and timing depends on whether and when the entries liquidated. Ask your broker.
Will the new robotics and machinery Section 232 action add a tariff on molds?
Not yet. Proclamation 11077 imposed no tariffs and named no HTS codes. Commerce and USTR report on negotiations by about April 26, 2027, after which the President may act.
This article is general education, not legal, customs or investment advice. Rates change; confirm with a licensed customs broker.
Sources
- HTS 8480.71.80, 2026 HTS Revision 23
- Usebase HTS 8480.71.80 with Section 301 List 1 history
- White House, Annex III Temporary Reduction List for Section 232 Steel and Aluminum Derivatives
- Husch Blackwell, Proclamation 11021, April 2, 2026
- Federal Register, Further Adjusting the Tariff Regimes for Imports of Aluminum, Steel, and Copper, June 2026
- Congressional Research Service, Section 232 Tariffs on Steel and Aluminum, September 17, 2026
- Steptoe, additional steel and aluminum derivative products, August 2025
- Gateway Lines, HTS 8480.71.80.45 duty stack from China
- Wove, HTS 8480.71.80.20 from China
- Holland and Knight, Section 301 forced labor tariffs on 60 countries, July 30, 2026
- GHY, Section 301 forced labor tariffs on 60 economies
- Strix, forced labor tariffs at 90 days, October 27, 2026
- ExFreight, IEEPA tariffs ended: refunds and what still applies, October 2026
- Ward and Smith, Section 122 tariff ruling, May 2026
- Mintz, White House proclamation on robotics, November 12, 2026
- EY, Section 232 robotics and industrial machinery conclusion
- CBP HQ 545256, assists including tools, dies and molds
- CBP HQ H031244, valuation and apportionment of assists
- CoreLMould, injection molding costs China vs US, Mexico and Vietnam, May 2026
- First Mold, US supply chains in tariff wars
Get The Benderson Brief
Five stories on robots, chips, power and AI money every weekday morning. Free. One click to leave.
Every figure in this piece links to its source. See our editorial standards. Nothing here is investment advice.



